Fandom

Wikitronics

Amplifier

62pages on
this wiki
Add New Page
Talk0 Share

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.

What is an Amplifier?Edit

An electronic device or electrical circuit that is used to boost (amplify) the power, voltage or current of an applied signal.

General characteristics of amplifiersEdit

Most amplifiers can be characterized by a number of parameters.

GainEdit

The gain is the ratio of output power to input power, and is usually measured in decibels (dB). (When measured in decibels it is logarithmically related to the power ratio: G(dB)=10log(Pout/Pin)).

Output dynamic rangeEdit

Output dynamic range is the range, usually given in dB, between the smallest and largest useful output levels. Since the lowest useful level is limited by output noise, this is quoted as the amplifier dynamic range.

Bandwidth and rise timeEdit

The bandwidth (BW) of an amplifier is usually defined as the difference between the lower and upper half power points. This is therefore also known as the −3 dB BW. Bandwidths for other response tolerances are sometimes quoted (−1 dB, −6 dB etc.).

As an example, a good audio amplifier will be essentially flat between twenty hertz to about twenty kilohertz (the range of normal human hearing), so the amplifier's usable frequency response needs to extend considerably beyond this (one or more octaves either side) and typically a good audio amplifier will have -3 dB points < 10 and > 65 kHz.

The rise time of an amplifier is the time taken for the output to change from 10% to 90% of its final level when driven by a step input.

Many amplifiers are ultimately slew rate limited (typically by the impedance of a drive current having to overcome capacitive effects at some point in the circuit), which may limit the full power bandwidth to frequencies well below the amplifiers frequency response when dealing with small signals.

For a Gaussian response system (or a simple RC roll off), the rise time is approximated by:

Tr * BW = 0.35, where Tr is in seconds and BW is in Hz.

Settling time and aberrationsEdit

Time taken for output to settle to within a certain percentage of the final value (say 0.1%). This is usually specified for oscilloscope vertical amplifiers and high accuracy measurement systems.

Slew rateEdit

Slew rate is the maximum rate of change of output variable, usually quoted in volts per second (or microsecond).

NoiseEdit

This is a measure of how much noise is introduced in the amplification process. Noise is an undesirable but inevitable product of the electronic devices and components. It is measured in either decibels or the peak output voltage produced by the amplifier when no signal is applied.

EfficiencyEdit

Efficiency is a measure of how much of the input power is usefully applied to the amplifier's output. Class A amplifiers are very inefficient, in the range of 10–20% with a max efficiency of 25%. Modern Class AB amps are commonly between 35–55% efficient with a theoretical maximum of 78.5%. Commercially available Class D amplifiers have reported efficiencies as high as 97%. The efficiency of the amplifier limits the amount of total power output that is usefully available. Note that more efficient amplifiers run much cooler, and often do not need any fans even in multi-kilowatt designs.

LinearityEdit

An ideal amplifier would be a totally linear device, but real amplifiers are only linear within certain practical limits. When the signal drive to the amplifier is increased, the output also increases until a point is reached where some part of the amplifier becomes saturated and cannot produce any more output; this is called clipping, and results in distortion.

Some amplifiers are designed to handle this in a controlled way which causes a reduction in gain to take place instead of excessive distortion; the result is a compression effect, which (if the amplifier is an audio amplifier) will sound much less unpleasant to the ear. For these amplifiers, the 1dB compression point is defined as the input power (or output power) where the gain is 1dB less than the small signal gain.

Linearization is an emergent field, and there are many techniques, such us feedforward, predistortion, postdistortion, EER, LINC, CALLUM, cartesian feedback, etc., in order to avoid the undesired effects of the non-linearities.

Electronic amplifiersEdit

There are many type of electronic amplifiers for different applications.

One common type of amplifier is the electronic amplifier, commonly used in radio and television transmitters and receivers, high-fidelity ("hi-fi") stereo equipment, microcomputers and other electronic digital equipment, and guitar and other instrument amplifiers. Its critical components are active devices, such as vacuum tubes or transistors.

Amplifier classesEdit

Amplifiers are commonly classified by the conduction angle (sometimes known as 'angle of flow') of the input signal through the amplifying device; see electronic amplifier.

Class AEdit

Where efficiency is not a consideration, most small signal linear amplifiers are designed as Class A, which means that the output devices are always in the conduction region. Class A amplifiers are typically more linear and less complex than other types, but are very inefficient. This type of amplifier is most commonly used in small-signal stages or for low-power applications (such as driving headphones).

Class BEdit

In Class B, there are two output devices (or sets of output devices), each of which conducts alternately for exactly 180 deg (or half cycle) of the input signal.

Class ABEdit

Class AB amplifiers are a compromise between Class A and B, which improves small signal output linearity; conduction angles vary from 180 degrees upwards, selected by the amplifier designer. Usually found in low frequency amplifiers (such as audio and hi-fi) owing to their relatively high efficiency, or other designs where both linearity and efficiency are important (cell phones, cell towers, TV transmitters).

Class CEdit

Popular for high power RF amplifiers, Class C is defined by conduction for less than 180° of the input signal. Linearity is not good, but this is of no significance for single frequency power amplifiers. The signal is restored to near sinusoidal shape by a tuned circuit, and efficiency is much higher than A, AB, or B classes of amplification.

Class DEdit

Class D amplifiers use switching to achieve a very high power efficiency (more than 90% in modern designs). By allowing each output device to be either fully on or off, losses are minimized. A simple approach such as pulse-width modulation is sometimes still used; however, high-performance switching amplifiers use digital techniques, such as sigma-delta modulation, to achieve superior performance. Formerly used only for subwoofers due to their limited bandwidth and relatively high distortion, the evolution of semiconductor devices has made possible the development of high fidelity, full audio range Class D amplifiers, with S/N and distortion levels similar to their linear counterparts.

Other classesEdit

There are several other amplifier classes, although they are mainly variations of the previous classes. For example, Class H and Class G amplifiers are marked by variation of the supply rails (in discrete steps or in a continuous fashion, respectively) following the input signal. Wasted heat on the output devices can be reduced as excess voltage is kept to a minimum. The amplifier that is fed with these rails itself can be of any class. These kinds of amplifiers are more complex, and are mainly used for specialized applications, such as very high-power units. Also, Class E and Class F amplifiers are commonly described in literature for radio frequencies applications where efficiency of the traditional classes deviate substantially from their ideal values. These classes use harmonic tuning of their output networks to achieve higher efficiency and can be considered a subset of Class C due to their conduction angle characteristics.

Power AmplifierEdit

The term "power amplifier" is a relative term with respect to the amount of power delivered to the load and/or sourced by the supply circuit. In general a power amplifier is designated as the last amplifier in a transmission chain and is the amplifier stage that typically requires most attention to power efficiency. For these reasons, a power amplifier is typically any of the above-mentioned classes except Class A.

Vacuum tube (valve) amplifiersEdit

According to Symons, while semiconductor amplifiers have largely displaced valve amplifiers for low power applications, valve amplifiers are much more cost effective in high power applications such as "radar, countermeasures equipment, or communications equipment" (p. 56). Many microwave amplifiers are specially designed valves, such as the klystron, gyrotron, traveling wave tube, and crossed-field amplifier, and these microwave valves provide much greater single-device power output at microwave frequencies than solid-state devices (p. 59).[1]

Transistor amplifiersEdit

The essential role of this active element is to magnify an input signal to yield a significantly larger output signal. The amount of magnification (the "forward gain") is determined by the external circuit design as well as the active device.

Many common active devices in transistor amplifiers are bipolar junction transistors (BJTs) and metal oxide semiconductor field-effect transistors (MOSFETs).Applications are numerous, some common examples are audio amplifiers in a home stereo or PA system, RF high power generation for semiconductor equipment, to RF and Microwave applications such as radio transmitters.

Operational amplifiers (op-amps)Edit

An operational amplifier is a solid state integrated circuit amplifier which employs external feedback for control of its transfer function or gain.

Fully differential amplifiers (FDA)Edit

A fully differential amplifier is a solid state integrated circuit amplifier which employs external feedback for control of its transfer function or gain. It is similar to the operational amplifier but it also has differential output pins.

Video amplifiersEdit

These deal with video signals and have bandwidths of about 5 MHz. Certain requirements for step response and overshoot are necessary in order for acceptable TV images to be presented.

Oscilloscope vertical amplifiersEdit

These are used to deal with video signals to drive an oscilloscope display tube and can have bandwidths of about 500 MHz. The specifications on step response, rise time, overshoot and aberrations can make the design of these amplifiers extremely difficult. One of the pioneers in high bandwidth vertical amplifiers was the Tektronix company.

Distributed amplifiersEdit

These use transmission lines to temporally split the signal and amplify each portion separately in order to achieve higher bandwidth than can be obtained from a single amplifying device. The outputs of each stage are combined in the output transmission line. This type of amplifier was commonly used on oscilloscopes as the final vertical amplifier. The transmission lines were often housed inside the display tube glass envelope.

Microwave amplifiersEdit

Travelling wave tube (TWT) amplifiersEdit

It is used for high power amplification at low microwave frequencies. They typically can amplify across a broad spectrum of frequencies; however, they are usually not as tunable as klystrons.

KlystronsEdit

Very similar to TWT amplifiers, but more powerful and with a specific frequency "sweet spot". They generally are also much heavier than TWT amplifiers, and are therefore ill-suited for light-weight mobile applications. Klystrons are tunable, offering selective output within their specified frequency range.

Musical instrument (audio) amplifiersEdit

An audio amplifier is usually used to amplify signals such as music or speech.

Other amplifier typesEdit

Carbon microphoneEdit

One of the first devices used to amplify signals was the carbon microphone (effectively a sound-controlled variable resistor). By channeling a large electric current through the compressed carbon granules in the microphone, a small sound signal could produce a much larger electric signal. The carbon microphone was extremely important in early telecommunications; analog telephones in fact work without the use of any other amplifier.

Magnetic amplifierEdit

A magnetic amplifier is a transformer-like device that makes use of the saturation of magnetic materials to produce amplification. It is a non-electronic electrical amplifier with no moving parts. The bandwidth of magnetic amplifiers extends to the hundreds of kilohertz.

An Amplidyne(Amplidyne redirects to this article) or Rototrol is a rotating machine like an electrical generator that provides amplification of electrical signals by the conversion of mechanical energy to electrical energy.

Optical amplifiersEdit

Optical amplifiers amplify light through the process of stimulated emission.

Miscellaneous typesEdit

  • There are also mechanical amplifiers, such as the automotive servo used in braking.
  • Relays can be included under the above definition of amplifiers, although their transfer function is not linear (that is, they are either open or closed).
  • Also purely mechanical manifestations of such digital amplifiers can be built (for theoretical, didactical purposes, or for entertainment), see e.g. domino computer.
  • Another type of amplifier is the fluidic amplifier, based on the fluidic triode.

Junction Transistor AmplifiersEdit

Since a junction transistor is a three-terminal device and there are four input-output terminals, one of the transistor terminals must be common to the input and output circuits. This leads to the names "common emitter", etc for the three basic types of amplifiers.

NPN Common Emitter AmplifierEdit

A common emitter is a type of electronic amplifier stage based on a bipolar transistor in series with a load element such as a resistor. The term "common emitter" refers to the fact that the emitter node of the transistor (indicated by an arrow symbol) is connected to a "common" power rail, typically the 0 volt reference or ground node. The collector node is connected to the output load, and the base node acts as input.

ApplicationsEdit

Common emitter circuits are used to amplify weak voltage signals, such as the faint radio signals detected by an antenna. They are also used in a special analog circuit configuration known as a current mirror, where a single shared input is used to drive a set of identical transistors, each of whose current drive output will be nearly identical to each other, even if they are driving dissimilar output loads.

Also on Fandom

Random Wiki